我们都知道不管是哪一种设备在安装或者使用之前都会进行尝试启动运行这一环节，有利于我们提早发现问题不至于影响到使用效果以及效率，自动上料搅拌车也是如此，那么该设备在安装试车时应该注意什么呢？

　　We all know that no matter what kind of equipment will try to start the operation before installation or use, which is conducive to our early discovery of problems and will not affect the use effect and efficiency. The same is true for automatic feeding mixer. So what should we pay attention to when installing the equipment in the test run?

　　自动上料搅拌车设备应安装在水平的混凝土基础上，用地脚螺栓固定；安装时应注意主机体与水平的垂直；安装后检查各部位螺栓有无松动及主机仓门是否紧固，如有请进行紧固；按设备的动力配置电源线和控制开关；检查完毕，进行空负荷试车。

　　Automatic feeding mixer equipment should be installed on the level of concrete foundation, fixed with foot bolts; Installation should pay attention to the main body and horizontal vertical; After installation, check whether the bolts in each part are loose and whether the door of the main engine bin is fastened. If yes, please tighten it. Power line and control switch are configured according to the power of the equipment; After inspection, no-load test is carried out.

　　此外，机器的维护工作做的好会让试车过程变得更加顺利，操作人员所需要的做的事项包含：轴承担负机器的全部负荷，所以良好的润滑对轴承寿命有很大的关系，它直接影响到机器的使用寿命和运转率，因而要求注入的润滑油必须清洁，密封必须良好，；新安装的轮箍容易发生松动必须经常进行检查。

　　In addition, the maintenance of the machine work well done will make trial process more smoothly, operators need to do items include: all the load bearing for machine, so good lubrication for the bearing life has a great relationship, it directly affects the service life of machine and availability, and requirements into lubricating oil must be clean and seal must be good,; The newly installed wheel is easy to loose and must be checked frequently.

　　注意机器各部位的工作是否正常；注意检查易磨损件的磨损程度，随时注意更换被磨损的零件；放活动装置的底架平面，应出去灰尘等物以免机器遇到不能破碎的物料时活动轴承不能在底架上移动，以致发生严重事故；轴承油温升高，应立即停车检查原因加以消除。；转动齿轮在运转时若有冲击声应立即停车检查，并消除故障。

　　Pay attention to whether all parts of the machine work normally; Pay attention to check the wear degree of easy to wear parts, pay attention to replace worn parts at any time; Put the chassis plane of the mobile device, should be out of the dust and other things in order to avoid the machine can not be broken when the material movable bearing can not move on the chassis, resulting in a serious accident; Bearing oil temperature rise, should immediately stop to check the cause to eliminate. ; If there is a sound of impact when the rotating gear is running, it should be stopped immediately for inspection and fault elimination.

　　每次装料前用水冲洗进料口，使进料口在装料时保持湿润；在装料的同时向随车自带的清洗用水水箱中注满水；装料后冲洗进料口，洗净进料口附近残留的混凝土；在车辆回程时保持混凝土贮罐正向慢速转动；下次装料前切记放掉混凝土贮罐内的污水；每天收工时彻底清洗混凝土贮罐及进出料口周围自动。

　　Rinse the inlet with water before loading each time, so that the inlet is kept wet when loading; Fill the cleaning water tank with water when loading the material; After loading, wash the feed port and clean the residual concrete near the feed port; Keep the concrete storage tank moving slowly forward when the vehicle returns; Remember to discharge the sewage in the concrete storage tank before loading the next time; Every day at the end of the work thoroughly clean the concrete tank and material inlet and outlet around the automatic.

　　自动上料搅拌车的空负荷试车有多个注意事项的相关内容讲解完毕，希望能够带给您帮助！当然如果您有什么问题要咨询，可以点击这里来网站www.jfhntjbj.com联系我们的客服人员。

　　The empty load test of automatic feeding mixer has multiple matters needing attention. I hope to help you! Of course, if you have any questions to consult, you can click here to the website www.jfhntjbj.com to contact our customer service staff.