What problems should be paid attention to when adding lubricant for self feeding small row mixer?

机械设备（例如自上料小行型搅拌车）需要不时润滑，以在长期使用中保持良好的运行性能。那么，在设备中添加润滑剂时应注意什么？

Mechanical equipment (such as self feeding small row mixer) needs to be lubricated from time to time to maintain good operation performance in long-term use. So, what should be paid attention to when adding lubricant to the equipment?

1.在操作过程中，请勿对自上料小行型搅拌车进行修理和润滑。

1. Do not repair and lubricate the self feeding small row mixer during operation.

2.定期在每个注油嘴中添加黄油，并每4小时对轴端密封处的油进行润滑，并每周排干一次。

2. Regularly add grease to each nozzle, lubricate the oil at the shaft end seal every 4 hours, and drain off once a week.

3.使用自上料小型搅拌车后，根据需要在每个润滑点添加必要的润滑剂（滚筒轴，滚筒，钢丝绳和其他有效部件）。

3. Add necessary lubricant (drum shaft, drum, wire rope and other effective parts) at each lubrication point as required after using the small row mixer.

4.自上料小型搅拌车的减速器的齿轮和轴承通过齿轮旋转将油溅入油箱的内壁，并流入轴承进行润滑。变速箱油位应保持在燃油表的两条线之间。油位太高或太低都会导致每个组件的温度升高或润滑不良，从而增加功率损耗并导致机器运行不佳。

4. The gear and bearing of the reducer of the small row mixer truck will splash the oil into the inner wall of the oil tank through the rotation of the gear and flow into the bearing for lubrication. The transmission oil level should be maintained between the two lines of the fuel gauge. If the oil level is too high or too low, the temperature of each component will rise or the lubrication will be poor, which will increase the power loss and cause the machine to run poorly.

5.选用自上料小型搅拌车的润滑油应具有一定的粘度和粘度温度特性，凝固点低，氧化稳定性好，无机械杂质和水分，无腐蚀和耐磨材料。其质量指标应符合标准。

5. The lubricating oil of self feeding small row mixer should have certain viscosity and viscosity temperature characteristics, low freezing point, good oxidation stability, no mechanical impurities and moisture, no corrosion and wear-resistant materials. The quality index should meet the national standard.

自上料小型搅拌车用于润滑，减少磨损并延长部件寿命。但是，添加润滑剂时需要采取一些预防措施。应该在前150个小时和300个小时内更换新机器，以在测试过程中未完全的灰尘。工作时，请务必检查油位并及时添加。

Self feeding small row mixer is used for lubrication, reducing wear and prolonging the service life of components. However, some precautions need to be taken when adding lubricants. A new machine should be replaced within the first 150 hours and 300 hours to eliminate dust that was not completely removed during the test. When working, please check the oil level and add it in time.

自上料小型搅拌车添加润滑剂注意了解就是这些，你明白了吗？

Add lubricant from the small line mixer, and understand that's all. Do you understand?
自动上料搅拌车