搅拌一体机它是行业中使用很广泛的，搅拌一体机有时受到淡季的影响，会闲置一段时间，那么搅拌一体机闲置时怎么保养呢？如何预防搅拌一体机事故发生呢？下面工作人员就向大家介绍下：

The all-in-one mixer is widely used in the industry. Sometimes it is affected by the off-season and will be idle for a period of time. How to maintain the all-in-one mixer when it is idle? How to prevent mixing machine accidents? The following staff will introduce to you:

1.防变形

1. Anti deformation

搅拌一体机的弹簧、传动带、杆、轮胎等零件由于长期受力或放置不当会产生塑性变形，为此应在机架下面加以适当的支撑，使轮胎不承受负载，饲料搅拌机上的所有压紧或拉开的弹簧须放松。拆下传动带在室内妥善保管，有些拆下的易变形零件如杆要放平或垂直挂起，另外拆下的零件如轮胎、输种管等保管时要防止挤压变形。

The spring, transmission belt, rod, tire and other parts of the mixing machine will produce plastic deformation due to long-term stress or improper placement. Therefore, proper support should be provided under the frame to make the tire not bear the load. All compressed or pulled springs on the feed mixer must be loosened. The removed drive belt shall be properly kept indoors. Some easily deformed parts, such as rods, shall be placed flat or hung vertically. In addition, the removed parts, such as tires and seed delivery pipes, shall be protected from crushing deformation.

2.防锈蚀

2. Rust prevention

搅拌一体机机作业完毕后，须外部泥垢，清理工作机构内的饲料、杂物，必要时用水或油清洗。清洗各润滑部位，并重新进行润滑，对所有摩擦工作面，如犁铧、犁壁、开沟器、锄铲等须擦净后涂机油，贴纸，以减少与空气接触氧化的机会。

After the operation of the mixing machine is completed, the external dirt must be removed, the feed and sundries in the working mechanism must be cleaned, and if necessary, water or oil must be used for cleaning. Clean all lubricating parts and re lubricate them. Clean all friction working surfaces, such as ploughshare, plough wall, furrow opener, hoe and shovel, and then apply oil and stickers to reduce the opportunity of air contact oxidation.

复杂精密的机具放在阴凉、干燥、通风的室内保管，等简单机具，可以露天保管，但要放在地势较高、干燥、不受阳光直射的地方，能搭棚遮盖，凡与地面直接接触的零件，应用木板或砖支起，脱落的防护漆要重新涂好。

Complex and precise machines and tools can be stored in a cool, dry and ventilated room, and simple machines and tools can be stored in the open air, but they should be placed in a higher, dry place that is not exposed to direct sunlight and can be covered by a shed. All parts that directly contact the ground should be supported by wood or bricks, and the fallen protective paint should be repainted.

3.防腐朽

3. Anti corrosion

霉烂木制的零件由于受微生物的作用以及雨淋、风吹、日晒而腐朽、和变形，有效的保管方法是在木料外表涂上油漆，置于干燥的地方，不要受到日晒、雨淋，这类制品不应在露天放置，应该拆下清洗晒干后，存放在室内干燥和能防虫、防鼠害的地方。

Moulded wooden parts are subject to decay and deformation due to the effect of microorganisms, rain, wind and sun. The effective storage method is to paint the surface of the wood and place it in a dry place. It should not be exposed to sun and rain. Such products should not be placed in the open air. They should be removed, cleaned and dried, and stored indoors in a dry place that can prevent insects and rats.

对长期停放的搅拌一体机应详细记载机具的技术状态、附属装置、备件、工具等，各种机具应由专人保管，严禁拆卸零件作其他用，如没有库房，机具在室外停放时，应将电动机、传动带等易丢件拆下来并作好标记，存放在室内。关注我们网站http://www.jfhntjbj.com了解更多的详细内容！

For the mixing machine that has been parked for a long time, the technical status, accessory devices, spare parts, tools, etc. of the machines and tools shall be recorded in detail. All machines and tools shall be kept by a specially assigned person. It is strictly prohibited to remove parts for other purposes. If there is no warehouse, when the machines and tools are parked outdoors, the easily lost parts such as motors, transmission belts, etc. shall be removed, marked, and stored indoors. Follow our website http://www.jfhntjbj.com Learn more!