如果自动上料搅拌车在使用过程中出现防锁系统故障，将影响自动上料搅拌车的正常运行。但是，如果自动上料搅拌车的防抱死系统出现故障，必须及时，否则会影响施工效率。如何检查自动上料搅拌车的锁定系统？

If the anti lock system fault occurs during the use of the automatic feeding mixer, the normal operation of the automatic feeding mixer will be affected. However, if the anti lock system of the automatic feeding mixer fails, it must be solved in time, otherwise the construction efficiency will be affected. How to check the locking system of automatic feeding mixer?

1.检查自动上料搅拌车的停车制动器是否完全松动。

1. Check whether the parking brake of the automatic feeding mixer is completely loose.

2.检查自动上料搅拌车的制动罐液位是否符合本手册的要求。

2. Check whether the brake tank level of the automatic feeding mixer meets the requirements of this manual.

3.检查自动上料搅拌车的所有制动管路是否有损坏和泄漏迹象。

3. Check all brake pipes of automatic feeding mixer for damage and leakage.

4.检查防抱死系统中的所有保险丝是否完好，电线是否损坏，以及插座是否牢固。

4. Check whether all the fuses in the anti lock system are in good condition, whether the wires are damaged, and whether the socket is firm.

5.检查电池容量和电压是否符合要求，以及正负极线之间的连接是否可靠。

5. Check whether the battery capacity and voltage meet the requirements, and whether the connection between the positive and negative wires is reliable.

6.检查防抱死系统和ECI_I连接器是否牢固连接。

6. Check anti lock system and ECI_ I connector is firmly connected.

7.检查电路连接是否有腐蚀，损坏，松动或接触不良。ABS的每根接地线的接地是否可靠。

7. Check the circuit connection for corrosion, damage, looseness or poor contact. Whether the grounding wire of ABS is reliable.

8.检查轮胎是否符合要求。

8. Check whether the tire meets the requirements

9.检查自动上料搅拌车的轮子是否转动，轮毂的轴承间隙是否正常。

9. Check whether the wheels of the automatic feeding mixer rotate and whether the bearing clearance of the hub is normal.

自动上料搅拌车的程序

Safety procedure of automatic feeding mixer

1.在驾驶之前，您必须仔细检查车辆的状况，以确保车辆能够驾驶。

1. Before driving, you must carefully check the condition of the vehicle to ensure that the vehicle can drive safely.

2.当自动上料搅拌车停放在露天时，搅拌桶应在装料前翻转，并应排出积聚的水和碎屑，以确保混凝土的质量。

2. When the automatic loading mixer truck is parked in the open air, the mixing bucket should be turned over before loading, and the accumulated water and debris should be discharged to ensure the quality of concrete.

3.运输混凝土时，确保倾斜槽牢固放置，防止因松动而摆动，行人在行驶中受伤或影响其他车辆的正常运行，同时注意避免混凝土溢出和污染地面。

3. When transporting concrete, make sure that the inclined groove is firmly placed to prevent swinging due to looseness, pedestrian injury or affecting the normal operation of other vehicles, and pay attention to avoid concrete overflow and pollution of the ground.

4.自动上料搅拌车不应运输混凝土超过搅拌站规定的时间。在运输混凝土的途中，搅拌筒不应长时间停止，以防止混凝土的分离。驾驶员应始终注意具体情况，并在发现异常时通知主控室，并申请。

4. The automatic loading mixer shall not transport concrete beyond the specified time of mixing station. During the transportation of concrete, the mixing drum shall not be stopped for a long time to prevent the separation of concrete. The driver should always pay attention to the specific situation and inform the main control room of any abnormality and apply for treatment.

5.当混凝土安装在车内时，现场的停滞时间不得超过1小时。如果超时，应要求现场负责人及时处理。

5. When the concrete is installed in the vehicle, the site stagnation time shall not exceed 1 hour. In case of overtime, the person in charge of the site shall be required to deal with it in time.

自动上料搅拌车的防抱死系统以及程序介绍就是这样了，希望对你有帮助。

This is the introduction of anti lock system and safety program of automatic feeding mixer. I hope it can help you.