概述:4方自动上料搅拌车的零件磨损应该怎么儿注意呢?我们一起来看看吧。How should we pay attention to the wear of parts of the
4方
自动上料搅拌车的零件磨损应该怎么儿注意呢?我们一起来看看吧。
How should we pay attention to the wear of parts of the 4-way automatic feeding mixer? Let's have a look.
1.维持自动送料混合器设备的额定负载
1. maintain rated load of automatic feeding mixer equipment
像这样的工程机械的负载性质和尺寸对设备部件的损失具有重要影响。当零件的载荷高于设计时,一般机械零件的磨损会随着载荷的增加而增加。当施加工作载荷时,其部件的磨损将继续增加。
The load properties and dimensions of such construction machinery have important influence on the loss of equipment components. When the load of parts is higher than the design, the wear of general mechanical parts increases with the increase of load. When the working load is applied, the wear of its components will continue to increase.
2.及时清洁,以减少机械杂质对设备的影响
2. clean in time to reduce the influence of mechanical impurities on the equipment
机械杂质通常指的是施工机械本身在使用过程中产生的灰尘,污垢和其他材料以及一些金属碎屑和油渍。一旦这些杂质到达机器的工作表面之间,危险就很大:不仅摩擦增加,而且燃料消耗也增加。它还会破坏润滑油膜并刮擦配合表面。
Mechanical impurities usually refer to dust, dirt and other materials produced by construction machinery itself during the use process, as well as some metal debris and oil stains. Once these impurities reach the working surface of the machine, the danger is great: not only friction increases, but also fuel consumption. It also destroys the lubricant film and scrapes the mating surface.
3.防止4方自动上料搅拌车部件腐蚀
3. prevent the corrosion of parts of the 4-way automatic feeding mixer
腐蚀作用于零件,有时不容易被发现,很容易被忽视,而且更有害。雨水,空气中的化学物质等通过机械部件的管道,狭缝等渗入机器,并腐蚀部件。腐蚀部件的持续工作也会加速机器的磨损并增加机械故障。这要求管理人员和操作人员根据当地的当地天气条件和现场条件采取合理的施工安排,尽量减少对机械部件的化学腐蚀损害。
Corrosion acts on parts, sometimes not easily found, easily ignored, and more harmful. Rainwater, chemicals in the air, etc. penetrate the machine through the pipes and slits of mechanical parts, and corrode the parts. The continuous operation of corrosive parts also accelerates the wear of the machine and increases the mechanical failure. This requires management and operators to take reasonable construction arrangements according to local local weather conditions and site conditions, and minimize chemical corrosion damage to mechanical parts.
4.保持4方自动上料搅拌车部件的合理温度
4. keep the reasonable temperature of the parts of the 4-way automatic feeding mixer
在工作中,每个组件的温度都有其自己的正常范围。温度过高或过低都会影响零件的强度,因此必须用冷却液和润滑油控制某些零件的温度,使其在合理的温度范围内工作。
In operation, the temperature of each component has its own normal range. Too high or too low temperature will affect the strength of parts, so the temperature of some parts must be controlled with coolant and lubricating oil to work within a reasonable temperature range.
4方自动上料搅拌车
4-way automatic feeding mixer
4方自动上料搅拌车的刹车技巧
The brake technique of the 4-way automatic feeding mixer
一是下坡刹车
First, the downhill brake
按下挤压尾部系统,然后挤压前部系统,目的是防止汽车前部下沉过多,并积极增加尾轮的重量,以免压在桅杆上。
First press the extrusion tail system, then the front system, in order to prevent the front of the car from sinking too much, and actively increase the weight of the tail wheel to avoid being pressed on the mast.
二,使用脚趾和脚底之间的力来踩刹车。
Second, use the force between the toe and the foot to apply the brake.
使用脚趾制动器不如使用脚底快。它可以瞬间将整个制动踏板推到,以化制动能力。从人们通常操作制动器的方式可以看出驾驶水平。当按下制动器时,汽车立即停止,或者当汽车停止时,它不能停止。这不是驾驶大师的表现。
Using toe brake is not as fast as using the sole of the foot. It can momentarily push the entire brake pedal to the end to maximize the braking capacity. The driving level can be seen from the way people normally operate the brakes. When the brake is pressed, the car stops immediately or it cannot stop when the vehicle stops. It's not a driver's performance.
三,乘客制动稳定
Third, the passenger braking is stable
当后座上有乘客时,汽车头部和尾部的重量相对平均,但随着汽车重量的增加,惯性也增加,并且所需的制动力大大提高。当增加制动器时,后座乘客可能会撞到椅子上,因为他们没有准备好保护。只要您教导坐着的乘客坐下,您就可以它们。
When there are passengers in the back seat, the weight of the head and tail of the car is relatively average, but with the increase of the vehicle weight, the inertia increases, and the braking force required is greatly improved. When the brakes are added, the rear seat passengers may hit the chair because they are not ready to protect. You can solve them as long as you teach the seated passengers to sit down.
4方自动上料搅拌车的刹车技巧以及减少零件磨损的方法就在这里了,希望对你有帮助。
The brake skills of the 4-way automatic feeding mixer and the method of reducing the wear of parts are here. I hope it will help you.