Automatic feeding mixer in peacetime to carry out regular maintenance, this is a lot of people know. But you know that maintenance is also needed during transportation.

发动机工作前期，水温上千很快;当水温表指示80后，升温速度减慢，则标明节温器工作正常。反之，若水温一贯增加很快，当内压抵达一定程度时，沸水俄然溢出，则标明主阀门有卡滞，俄然翻开。在水温表指示70℃-80℃时，翻开散热器盖和散热器放水开关，用手感其水温，若均扎手说明节温器工作正常;若散热器加水口处水温低，且散热器上水室进水管处无水流出或流水甚微，说明节温器主阀门无法翻开。有卡滞或关闭不严的节温器应拆下清洗或批改，不可姑息运用。

In the early stage of engine operation, the water temperature is very fast; when the water temperature gauge indicates 80, and the heating rate slows down, it indicates that the thermostat is working normally. On the contrary, if the water temperature always increases rapidly, when the internal pressure reaches a certain degree, boiling water suddenly overflows, indicating that the main valve is stuck and suddenly opens. When the water temperature gauge indicates 70 ℃ - 80 ℃, turn on the radiator cap and radiator drain switch, feel the water temperature by hand. If both hands are tight, the thermostat works normally; if the water temperature at the radiator water inlet is low, and there is no water outflow or little water flow from the water inlet pipe of the radiator upper water chamber, it indicates that the main valve of the thermostat cannot be opened. If the thermostat is stuck or not closed tightly, it should be removed for cleaning or correcting, and should not be used with palliative care.

运用沟通法，拆下发动机的空气滤清器，假定此时自动上料搅拌机主张机排出的不是黑烟，那说明是空气滤清器有严重的阻塞，应消弭阻塞或许变换滤芯，变换新的滤芯效果非常好。因为发动机喷油泵和调速器调整不恰当，使油嘴的喷油量太大，逾越了发动机的每个循环喷油数量，或许是有对比严重的后滴油现象等，构成供油量过大。

Using the communication method, remove the air filter of the engine. Assuming that the automatic charging mixer claims that the machine does not emit black smoke, it means that the air filter is seriously blocked. The blockage should be eliminated. Maybe the filter element should be changed and the effect of changing the new filter element is very good. Due to the improper adjustment of the engine fuel injection pump and governor, the fuel injection quantity of the nozzle is too large, which exceeds the fuel injection quantity of each cycle of the engine. Perhaps there is a relatively serious phenomenon of rear drip, which constitutes the excessive fuel supply.

Automatic feeding mixer

在装有涡轮增压设备的自动上料搅拌机柴油机，应按修补守则上的涡轮增压设备的缺陷确诊办法间断确诊与清扫，或选用置换法，即换用同类型的涡轮增压器，若沟通后没有黑色烟雾就能够证明柴油机冒黑烟是涡轮增压器损坏所发作的。柴油是碳氢化合物，假定发动机在短少氧气的条件下停息，简单构成停息不充分，不无缺，会导致部分没有无缺停息的碳元素构成游离碳，混入废气排出，导致发作了黑色的烟雾。

For the diesel engine with automatic charging mixer equipped with turbocharging equipment, the diagnosis and cleaning shall be conducted intermittently according to the defect diagnosis method of turbocharging equipment in the repair code, or the replacement method shall be used, that is, the same type of turbocharger shall be replaced. If there is no black smoke after communication, it can be proved that the black smoke of diesel engine is caused by the damage of turbocharger. Diesel oil is hydrocarbon. If the engine stops under the condition of short oxygen, the simple composition of the engine is not enough. If the stop is not enough, it will lead to the formation of free carbon from some carbon elements without lack of oxygen, which will be mixed into the exhaust gas to exhaust, resulting in the occurrence of black smoke.

翻开散热器加水口盖，若散热器内冷却水安静，则标明节温器工作正常，否则，则表明节温器工作异常。这是因为，在水温低于70℃时，节温器胀大筒处于缩短情况，主阀门关闭;当水温高于80℃时，胀大筒胀大，主阀门逐步翻开，散热器内循环水初步活动。

Open the radiator filler cap. If the cooling water in the radiator is quiet, it indicates that the thermostat is working normally; otherwise, it indicates that the thermostat is working abnormally. This is because when the water temperature is lower than 70 ℃, the expansion cylinder of the thermostat is in the condition of shortening, and the main valve is closed; when the water temperature is higher than 80 ℃, the expansion cylinder expands, the main valve gradually opens, and the circulating water in the radiator is initially activated.

用自动上料搅拌车过程中，遭受心小碰而没有及时批改，漆面呈现金属面显露的现象，在这段时间更应勤加间断漆面清洗，否则就会加剧“伤口”处的受伤水平。可是，要分外留神，漆面清洗很有必要，但补漆工作，就应尽量防止选择在湿润时期间断。

In the process of using the automatic feeding mixer, the paint surface shows the phenomenon of metal surface exposure due to small heart collision without timely correction. During this period, the paint surface should be cleaned frequently, otherwise the injury level at the "wound" will be aggravated. However, to pay special attention, it is necessary to clean the paint surface, but repair work, should try to prevent the choice of interruption in the wet period.

自动上料搅拌车不仅仅只是在停车了之后在进行保养，在运输行驶的过程中也是要进行保养的，大家在这两方面都要多加注意。

The automatic feeding mixer is not only for maintenance after parking, but also for maintenance during transportation. We should pay more attention to these two aspects.