经常使用自动上料机搅拌车，时间久了难免会出现故障，出现故障不要怕，小编来告诉你如何故障问题。

If you often use the mixer truck of the automatic feeder, it is inevitable that a failure will occur after a long time. Don't be afraid of the failure. I will tell you how to solve the problem.

1.自动上料搅拌车工作时有噪音检查滤芯清洗或更换检查吸油管路有无漏气拧紧或更换密封检查油的标号更换合适标号液压油检查泵、马达、万向轴等连接螺栓紧固连接螺栓油箱油位低补油。

1. When the automatic feeding mixer is working, there is noise. Check whether the filter element is cleaned or replaced. Check whether there is air leakage in the oil suction pipe. Tighten it or replace the seal. Check whether the oil label is correct. Replace the hydraulic oil with the appropriate label. Check whether the connecting bolts of the pump, motor, universal shaft, etc. are fastened. Connect the connecting bolts. The oil tank is filled with oil when the oil level is low.

2.搅拌罐起动慢检查滤芯清洗或更换检查吸油管路拧紧或更换密封检查油箱油位补油检查控制软轴连接或更换软轴。

2. Start the mixing tank slowly. Check whether the filter element is cleaned or replaced. Check whether the oil suction pipe is tightened or the seal is replaced. Check the oil level in the oil tank. Make up oil. Check whether the control flexible shaft is connected or replace the flexible shaft.

3.油温过高液压油标号不对(标号混用)更换合适标号液压油液压油脏更换液压油超负荷工作调整负荷冷却风扇不转，温控器损坏更换温控器泵吸空补油冷却器过油量不够补油液压件内泄严重更换有关零件检查滤油器(吸油)清洗或更换滤油器。

3. The oil temperature is too high. The hydraulic oil grade is incorrect (mixed grade). Replace the hydraulic oil with the proper grade. The hydraulic oil is dirty. Replace the hydraulic oil. The hydraulic oil is overloaded. Adjust the load. The cooling fan does not turn. The temperature controller is damaged. Replace the temperature controller. The pump suction and makeup oil coolers. The oil flow is insufficient. The hydraulic parts have serious internal leakage. Replace the relevant parts. Check the oil filter (oil suction). Clean or replace the oil filter.

4.搅拌罐不能转动无补油压力检查补油泵及油箱补油压力过低。检查油箱油位是否满足液压系统工作补充同企业同型号油液连接盘花键套内花键损坏更换连接盘或主泵通轴检查吸油管路是否断裂、被挤压更换或修理吸油管路排量控制拉线是否脱开连接好排量控制拉线检查伺服阀、销更换销控制油路被异物堵塞清晰油路滤油器太脏，清洗或更换滤油器。

4. The mixing tank cannot rotate without oil make-up pressure. Check that the oil make-up pressure of the oil make-up pump and oil tank is too low. Check whether the oil level in the oil tank meets the requirements of the hydraulic system. Replenish the oil of the same brand and model. Replace the spline inside the spline sleeve. Replace the connecting disc or the main pump shaft. Check whether the oil suction pipeline is broken, squeezed. Replace or repair the oil suction pipeline. Check whether the displacement control cable is disconnected. Check whether the servo valve and safety pin are connected. Replace the safety pin. Control the oil circuit is blocked by foreign matters. Clear the oil circuit. The oil filter is too dirty. Clean or replace the oil filter.

如何自动上料搅拌车出现的故障问题？以上就是问题的解答了，希望能够给您帮助，当然你要记住日常中好好维护设备。关注我们http://www.jfhntjbj.com，了解更多使用事项！

How to solve the failure problem of automatic feeding mixer? The above is the answer to the question. I hope it can help you. Of course, you should remember to maintain the equipment well in daily life. Follow us http://www.jfhntjbj.com , learn more!